Re: ADV7180 & ADV7391 SFL problem
hi, GuenterL, The waveforms of adv7391 output and adv7180 input are all ok,there are no pulses and glitches. The SFL signal is important in our design. Because i can not visit the dailymotion...
View ArticleRe: ADSP-21479, SPORT, the Buffer Status
could you check my thread out to see what the problem is?ADSP 21489 SPORT problem
View ArticleClik here to view.
Re: Power up rule for ADXL345
Dear Neil, Thank you for your response.We investigate in detail the environment which has ADXL345 based on your advice. Best Regards,George
View ArticleMy flash is not properly working
Hai good morning sir/madam, I am new for DSP. Present i am working on ADSP-21060 SHARC processor, in my single channel board my flash is not properly working. My flash is AM29LV017D. Initialization...
View ArticleRe: How to create an LDI file
Hai Colinj sir,Good Morning, I know how to crate an loader file for flash booting. But in my flash code LDI file is used instead of LDR file. But we don't know how he created the LDI file for this....
View ArticleRe: ADV7513: What work 0x48 bit 6 "Video Input Bus Reverse" ?
Hi DaveD. I was confirm the reverse operation in Eval Board (ADV7612 to ADV7511).The reverse operation is fine.However, it does not work where the customer has confirmed in the ADV7513. I heard...
View ArticleRe: AD9364 No-OS drivers
Hi Lakshmi, I had a similar error. It appears because you haven't generated the IP for axi_dmac. if you are in projects/fmcomms2/zc706: cd ../../../library/axi_dmacsource ./axi_dmac_ip.tcl an so on for...
View ArticleRe: ADF4360-0 : The VCO output is damping at changing VCO from 2.48GHz to...
Hi rbrennan, Thank you very much for your response.I understand that it is the band select process testing various frequency bands.We will do in line with your advices. Best regards, Nikkee
View ArticleTristate ADV7280-M and ADV7480 MIPI CSITx output
Dear Sir,Is it possible to configure ADV7280-M and ADV7480 MIPI CSITx output to tristate?Via the datasheet, it seem's ADV728x-M MIPI Tx can be programmed to enter the ultralow power state. In this...
View ArticleADV7630 36bit Deep Color
Hello all, Evaluation board of ADV7630 does not output correctively at input of 1080p 36bit deep color.ADV7630 can see that input signal is 12bit ( 12bit *3=36bit) signal when we read register at...
View ArticleRe: QPSK GENERATION (MATLAB HDLCODER)
Amruta, Unfortunately, this week I'm in a business trip so I'm not sure if I will be able to test your data. Regards,Dragos
View ArticleRe: Auto Sleep Mode in ADXL313
Hi Tao, 1. After inactivity interrupt, it will be changed to Sleep Mode.After activity interrupt during Sleep Mode, it will be changed to Measurement Mode from Sleep Mode.As it is named Auto Sleep...
View ArticleClik here to view.
Re: AD9364 No-OS drivers
Hi Lakshmi, Oscar is right. Please follow his advice. Thanks,Dragos
View ArticleRe: Recommended 1.8V regulator for 8 DDS chips
Hi rrosario ,I am going ahead with ADP3339 for my design.I am using one ADP3339 / 4 DDS(AD9959) chips.Thank you,Prakash
View ArticleRe: AD9361 no-OS manual gain control
Hi Pete, I assume that setting the gain works for you in MGC mode?The messages you are seeing are debug messages - you are in full gain table mode.Because debug message "Ignoring lmt/lpf/digital gains...
View ArticleCan I roll my own SPICE model?
I'd like to use a SPICE model for an ADG5212 in a simulation but there doesn't seem to be one. As I'm only really after a quick look-see to get a feel for the circuit behavoiur, can I use an equivalent...
View ArticleRe: AD9361 IBIS Model
Thanks for the reply. So are you saying that the common-mode range of the LVDS input is 825-1575mV? That is unusual for a LVDS input, which would normally work down to Vcm of 300mV or less. What is the...
View ArticleAD9739A-FMC-EBZ rev C vs. rev B changes
Hi EZ team, I have a customer that is experiencing some problems with the AD9739A-FMC-EBZ(rev C) They need to use AD9739A with an external clock signal (2.4GHz), which is generated with a Signal...
View ArticleRe: Blackfin Image Processing Toolbox - Link failed
Hi, Thanks for the details of the linker output. The li1060 error is a symptom of the problem highlighted by the li2060 warning. Basically you have code or data that has been tagged with the Input...
View ArticleRe: I wish to know the equivalent circuit of an input pin.
Hi DMN, In the PDF that I previously supplied the input resistor divider structures have a summed resistance > 12K.This is what you would typically see in an ADM489A if measured. The 12K datasheet...
View Article