Clik here to view.
Re: ADF4351 PLL programming question
Yes, it can be used as an output. But keep an eye on the load and signal power.
View ArticleRe: ADV7186 full data sheet
The ADV7186 is under NDA so you'll need to go through your local ADI Sales/FAE or distributor to get the rest of the documentation and purchase an evaluation board. ADV7186 Full Data Sheet
View ArticlePVP - THC0 Coefficient updated on-the-fly But not took effect.
Hi, I am using CameraPipe PVP as below, EPPI0 --> IPF0 --> THC0-->OPF0--DMA46Its working properly But if I update THC_MINTH or MAXTH register in running time, the change not affect the...
View ArticleRe: Questions about AD9279 Reference Design
1 sample = 16bits (of 1 channel). If you are not reading the DDR data the same as what you see in chipscope, it may be a need a cache flush (search for microblaze flush or invalidate cache).
View ArticleRe: ACP and ISRC support in SPDIF format
Hi Sandeep, I don't either-- but if it's in the original source data stream, then it will come out of the ADV7619 as well. Dave
View ArticleRe: SPI slave select in Software control
Hi Anand, If you refer to the Parallel Peripheral Interface chapter (Chapter 11) of the BF538 Hardware Reference Manual it explains that "The state of PPI_FS3 depends completely on the state of PPI_FS1...
View ArticleRe: continuos conversion mode in ad7195
Hi Reinhard, thanks for your reply.1) Do you always wait for DOUT/RDY# falling, before applying 0x58? Yes, I'm sure Ialways wait that the line DOUT/RDY goes to low before send 0x58.2)Do you capture...
View ArticleLimitations of using AD8352 amplifier with AD9434 ADC?
Hi Everyone, Are there any limitations of using the AD8352 amplifier with the AD9434 ADC? They are shown together in the ADC datasheet, but now the website for that part recommends a newer amplifier,...
View ArticleADUM3200 Working Voltage Specs?
I have a customer that is looking for a digital isolater, 2 channel, 1 input and 1 output. - Powered from 5V and 3.3V - The working voltage must be at least 1200VDC. - It must support a UL creep-age...
View ArticleADXL343 standby mode
Hi,I want to use the ADXL343 accelerometer in a design that needs very low power and I am wondering if the interrupts can work in standby mode? In the datasheet, I can read that no measurements are...
View ArticleClik here to view.
Re: Dose ADI have detailed document for ADradioNet?
Hi MMA, Thank you very much for the quick reply. The attached document does help me a lot!I'm looking forward to the launch of the community for ADradioNet. How could I find this community then?By the...
View ArticleRe: Question about the ADV7180 with the output picture shake
Dear GuenterL Yes! I have changed the source of the Vidoe, and had the same phenomenon. And did an another test that by a decode board behind ADV7180, and show the vidoe in LCD, and found the...
View Articlebuilding drivers for adsp-bf537 ez-kit lite in simulink
Hi,I'm using MATLAB/Simulink to build models for adsp-bf537 ez-kit lite but not all drivers' blocks are available in "analog devices blackfin/adsp bf537 ez-kit lite" library. so how could i build a...
View ArticleRe: Programming AD5122A
Hello, After bit of tweaking, the chip finally responded! Even though, it is supposed to work with standard I2C command, bit of fine tuning is always required. Thanks to Reinhard for helping me out...
View ArticleADF4351 Vref
Hi, Could someone help me to understand how the Vref is generated and used within ADF4351? In one of our board, Vref for ADF4351 is showing 350mV. For that component the lock detect is not going high...
View ArticleRe: Sigma Studio Ver 3.11 Build 1. Rev 1356 Mixer Bug?
Hi What processor are you using?
View ArticleDynamic bass boost in a 2.1 stereo design
Hi, I am designing a 2.1 stereo system using ADAU1702 and I want to make use of the dynamic bass boost block. My signal chain is: input -> parametric EQ -> 2-way crossover -> bass boost ->...
View ArticleRe: No UART communication when flashing SPI with u-boot
Hi, I am also getting same issue log ERROR:bfin-uclinux-ldr -l ~/tftpboot/u-boot.ldr.uart /dev/ttyUSB0 && kermit -l /dev/ttyUSB0 -b 57600 -C connectLoading LDR...
View ArticleCan ADIS16305 be used in Pitch and Yaw controlling?
Hi Experts, For low cost application, we can't use 6DoF IMU for drive monitoring systems. As the application needs, Yaw and Pitch are needed monitoring together by real time. I saw that ADIS16305 is...
View ArticleS1(revC)+ZC706 ADF4351 output frequency unstable
Hi All, i use s1(revC)+ZC706(or ML605),then ADF4351 output frequency unstable.but S1+zed not.PS:hdl(no vivado) and no-OS driver are newest.Please help me,thanks.
View Article