composite amplifier
I am sampath Bandara I need to construct composite amplifier so my desire gain is 45 and total bandwidth of 50 MHz with low noise and low offset voltage, high slew-rate. I highly appreciate if you can...
View ArticleRe: Sigmastudio algorithms
Hello Graeme, It sure seems like this block, Timer Coarse Long Time, is MIA. It doesn't show up in any SigmaStudio version I tried, from 3.10.4 to the latest beta. Best regards, Bob
View ArticleRe: About AD5700 Carrier Detect Off Timing
Hi David, Thank you for reply.I think so,HART SIGNALdoesnot knowthe MCUside.Therefore,you will not be ableto interpret thet5.Intable.5,do youhave timeprovisions ofthe falling edge of theCD from...
View ArticleRe: AD9361 About the results of the calibration.
Hi tlili. Is itmay beconsidered that there is noquadraturecalibrationcompletion statusregisterofRx? Best Regards.Hara
View ArticleRe: AD9361, AGC with LTE10 MHz configuration
Input signal is @752 MHz (carrier frequency = 751 MHz)Input level = -30 dBmEach time I read 0x1A7 it's changing but for example, I read back some value - -49 dBm, -74 dBm, --84 dBm, -78 dBm ... I...
View ArticleRe: Interfacing AD9633 eval board with ML605 using an ADI working reference...
Hi z00345up, Thank you for considering the AD9633. Indeed as you have discovered, the AD9633 is not one of the devices that is compatible with the FMC interposer (CVT-ADC-FMC-INTPZB) as-is. The problem...
View ArticleSigmaStudio Automatic Speaker EQ Usage
HiI would like to use Auto-EQ by ADAU1761 or ADAU1701 , I try to add this algorithm in DSP schematic sheet and open this algorithm. The Auto-EQ have to set a source response and it might need to load...
View ArticleBF60ｘ, driver type for USB0_VBC
Hi, Could you please provide quick answer for what is Driver Type="E" at BF60x USB0_VBC pin which is described in BF60x datasheet Rev.A, Table 15. ADSP-BF60x Designer Quick Reference at page.51 ?It...
View ArticleClik here to view.
ADI Sigmastudio question
Dear Sir,In Sigmastudio,Schematic==>Tree Tool Box ==>IO==>GPIO==>Output==>Interface WriteWhat's the Interface Write function?ADAU1761 can use Interface Write? Thanks.
View ArticleAD9736 Evaluation Tool with Xilinx board
Hi All,One of my customer is planning to utilize AD9680 14bit High-Speed ADC and AD9736 14bit High-Speed DAC for his new design.Prior to circuit design work, he is planing to make evaluation test by...
View ArticleADXL362 rotate motion
Hi, Have any about ADXL362 rotate motion application notes, driver or others?Thank you!Kevin
View ArticleAD80066 SHA mode circuit with offset control
Hi Could I have the recommended circuit for SHA mode with offset control?Datasheet RevA P19/20 Figure 24 say OFFSET terminal, 26PIN, connected to ground.But It can not control internal offset function,...
View ArticleRe: What is the Technique of PulSAR?
Thanks for reply.However, I can not figure it out why PulSAR can reach >16-bit of resolution from AN-931. It seems like a regular SAR process. How could it overcome the CMOS capacitor array accuracy...
View ArticleRe: RGB Receiver
Hi, Mani. You can use 80ohms for Rs. This is computed by using Ohm's law where current=31.5mA (found in the datasheet) and voltage=2.5V (your input voltage). You can also change this to a lower value...
View ArticleRe: RGB Receiver
Hi, Mani. Regarding the comparators of AD8145 used as voltage follower, we don't recommend doing this. It is better to tie off the inputs to known voltages if you will not use the comparators. Positive...
View ArticleRe: ADE7880 - How to set up for phase Harmonics monitoring / calculation
Hi Karen 1. VLEVEL: At PGA=2, full scale is 250mVpeak. Say, you have a 1000:1 attenuation network. Then 250Vpeak phase voltage will cause the ADCs to be at full scale. Hence, 250/sqrt(2) will be Vfs....
View ArticleAD9680-1000EBZ schematics
Hello All, Where can I find the schematics of AD9680-1000EBZ? Thank you for your help,Ricky
View ArticleRe: ADL5391 offset question
Hi Joel, Thanks for the reply.How exactly does figure 11 relate to the specification of output offset voltage (19mV) on page 3 of the datasheet? If figure 11 shows the offset voltages for X and Y...
View ArticleClik here to view.
Re: Question related to ADV7842 initialization
Hi Dave, As I know, my company has SLA assigned with Analog Devices, but there are some points, which our management should solve with yours. So I'm waiting when all will be clear and I'll receive the...
View ArticleADV7481 Schematic Symbol and PCB Lyout
We are using Cadence Orcad Schematic capture and Cadence Allegro for the PCB design. I note that there is eval board for ADV748x, could you post the schematic symbol and possibly layout for the...
View Article