Re: AD9361+Zedboard and AD9361_iiostream example
yes i have compile the last version for boot.bin and kernel .. i have get the master branch on the git repo. I checkout this how master.I make the boot.bin whit the xilinx design and the fsbl project...
View ArticleWhat AD-ADC-FMC Adapter Board (Rev A or Rev B) do I need to connect...
Dear colleagues,I can not figure out which model adapter board should I use to connect connect AD9467-200EBZ to ML605.AD9467 Evaluation Board, ADC-FMC Interposer & Xilinx Reference Design [Analog...
View ArticleRe: AD9361+Zedboard and AD9361_iiostream example
i have print the errno val on the segmentation falut on the petalinux host and errno value is 2p0p1p2p3. -->> Open iio device .. ... enabled channel -->> ch idx = 1...
View ArticleADV5113 input timing
Hello all, Is there any specification about input signal timing of ADV7513 ?Does ADV7513 need input of PCLK or data before register settings ?Our customer's system configuration is below two. Case...
View ArticleRe: ERROR: [Common 17-69] Command failed: Run 'synth_1' failed. Unable to open
Hi, I have just finished recompiling the project using the files that I've indicated with vivado 2013.4. The steps I've followed are described in http://wiki.analog.com/resources/fpga/docs/hdlI have...
View ArticleRe: AD844 CFOA
ok, that's a more involved setup than I would have expected from your first description ;-) The paper is somewhat involved, and I can't go through it in detail. But I believe, that you misinterprete...
View ArticleRe: AD9361+Zedboard and AD9361_iiostream example
This is surprising, I didn't expect this error code. This means that one file is missing, do you have the /dev/iio:deviceX nodes? Is the "cf-ad9361-dds-core-lpc" detected when you run iio_info?
View ArticleClik here to view.
Tx LO leakage improvement
Hello, The LO leakage is at -50dBc on the transmit side, while on my design the LO frequency is set to 70 MHz, and the output frequency is 71 MHz. According to the datasheet, this could be expected;...
View ArticleRe: AD9361+Zedboard and AD9361_iiostream example
and why TX 0.00 MSmp ?he don't trasmit directly on the TX1A and TX2A connector ?
View ArticleADV7619: minimum junction temperature?
Hi all There is mention of the maximum junction temperature to the data sheet,but there is no mention of the minimum junction temperature. Is the minimum junction temperature = lowest operating...
View ArticleRe: ADuCM320 IDAC and VDAC sink/source capability?
The IDACs source the large current – up to 150mA. But they do have thesmall current sink capability – few hundred uAs The VDACs can sink or source current – depending on whether the loadexternally is...
View ArticleADuCM320 IDAC and VDAC sink/source capability?
Analog Team- What is the sink/source specification for the VDAC and IDAC structure? The datasheet and manual 0-150mA full scale for the IDAC, and up to 500uA for VDAC assuming a 5kohm/100pf load. Are...
View ArticleRe: customize HDL reference code of AD9364 in LVDS mode
Hello, UG570 AD9361 Reference manual shows timing diagrams on TX path (starting from page 109). We provide the IP core so that you don't need to develop the interface, as it may involve considerable...
View ArticleADSP TS201 multiprocessor booting issue
Hi everyone!In our project, we have used 3-ADSP-TS201 processors that are connected in a multiprocessing environment. Here, the 'BMS' pin has been configured in the EPROM boot mode. However, after...
View ArticleRe: ADuCM320 IDAC and VDAC sink/source capability?
Page 6 of the data sheet shows 2ohm output impeadance for VDACs - is this correct or should it be 2kohm?
View ArticleRe: How to sample a periodic waveform at given points in the period?
Thanks Bob. That is exactly what I needed. I modified it slightly to take the count from a clean signal and read the data from a different one (my data signal is a bit messier and could cross zero a...
View ArticleADV7619: DATA OUTPUT TIMINGS?
Hi all I have a question about "DATA AND CONTROL OUTPUTS" of data sheet P6.Therefore prescribed t11, t12 are only typ levels, and the maximum is not listed.How do you guarantee the timing? In addition,...
View ArticleClik here to view.
Re: Control of Boston engineering FlexMC kit with ADI CM408F
Hello SheryWe cannot promise you much help on this as it is your own modification of the Simulink files provided by Boston Engineering, and as such, falls outside of what we would be able to provide...
View ArticleRe: AD-FMCOMMS3-EBZ Crystal
Ed: Refer to:AD-FMCOMMS2-EBZ Hardware [Analog Devices Wiki] The Epson crystal used on this board, has the generic part number “TSX-3225 40.0000MHZ” - however, the generic part number does not have the...
View Article