Clik here to view.
Re: Changing the ADV7611 resolution after connecting the video source
DaveD wrote: Hello, I can't help you with the Linux driver-- I don't know anything about it. There is another forum for it here: Linux and Microcontroller Device Drivers It sounds like that is where...
View ArticleRe: AD9625 Register Configuration + Linux
Hi Pablo- There are a small number of registers that are used for our ADCs that are identical to all ADCs. These register values are located in the lower numbered addresses. They control standard...
View ArticleRe: Changing the ADV7611 resolution after connecting the video source
Please take a look at the software guide/manual for ADV611: ADV7611 Design Support Files 1) Yes HPA_A-- with no hot plug signal, I'm not sure you could create a working system that is compatible with...
View ArticleRe: Does ADV7619 support BT.1120 output ?
Hello Marco, What color space? What pixel clocks? Dave
View ArticleRe: HMC1086F10 for Pulse Power Amplifier question?
Hello ryan-tsai, The HMC1086F10 is compatible with pulsed power applications.It is recommended that the pulsing of power be accomplished via the Vdd pins.Pulsing of power via the gates would provide...
View ArticleRe: External Reference Issue
Does anyone have additional information regarding the clock problem?
View ArticleAD9984 Power consumption
Hi All, I'm planning on using the AD9984 in a design where the power consumption is sensitive.I'm wondering if anyone has a typical power consumption when sampling SVGA@60Hz? Thanks, Enguerran
View ArticleRe: AD9978A:What is TC_RCPxx?
By using this register, for each region you can specify the time constant of the OB clamp loop. For example, the default register value of 9 means the time constant will be 2^9 pixels (512 pixels). So,...
View ArticleRe: Problem with ADIsimPower for ADP2442
It looks like the design may have a problem with so much output capacitance. You can either decrease the output capacitance or you may be able to increase the gain (set R8 to 200K). To have a better...
View ArticleClik here to view.
Re: Modifying Tx Path for FMCOMMS2 (ad9361)
Hi Lars,I mean that the execution gets stuck (infinite loop), no segfault, the function never returns.With a few prints, i found that during the rx buffer creation, the following are called...
View ArticleClik here to view.
Re: HMC244G16
Hello, I hope the information provided below will be helpful for your analysis. 1) We only have typical voltage and current specs for digital inputs at room temperature. The majority of digital input...
View ArticleClik here to view.
Re: ADAU1701 AUX ADC numeric range
Hello Tommaso, FYI, you can post SigmaDSP-related questions directly here: SigmaDSP Processors and SigmaStudio Development Tool The ADAU1701 datasheet page 36 states: "The SigmaDSP program reads this...
View ArticleRe: HMC244G16
For your information, HMC244G16 is not recommended for new designs. A new pin-to-pin compatible replacement product (HMC244AG16) will be offered soon with a PCN.
View ArticleRe: FMCOMMS5 Requirements
to start using the FMCOMMS5 board you need to have the ZC706 FPGA board. Between our board and the FPGA board you should be good to start testing. As far as doing other implementations, that will come...
View ArticleRe: ADXL375
Thank you for your feedback. I am sorry about the trouble you are experiencing and agree that is very different than before. However, we hope that you are able to work through this initial shock so...
View ArticleRe: Moving from AD9912 to AD9910
HiThe AD9910 and AD9912 are very similar with regards to the REF CLK input stage. Both are typically ac-coupled and the max input amplitude swing is around 1Vpp single-ended or 2Vpp differential. What...
View ArticleRe: AD9106 SRAM read/write
Hi - This inquiry is being handled through direct email. Thanks,Larry
View ArticleRe: Gerber or DXf files for HMC189AMS8E and HMC204MS8GE
I really appreciate to provide gerber files.Actually, our group has a plan testing both doubler chips on evaluation boards whether they are appropriate for our application or not. If possible, can we...
View ArticleSPDERROR 4001 - EVAL-ADIS LED1 not turning on
Hi, I have installed the SPD drivers, and have the IMU_Evaluation program. When I connect the EVAL-ADIS board, only LED2 illuminates indicating there is a connection, but LED1 does not turn on which...
View Article