Re: Output Protection Circuit for AD5755 ?
Hi, DerrickH as your information for external protection circuit, do you have any suggestion D1/D2 TVS diode spec or parts?from page 47 of latest data sheet, there is not description much detail.Thank...
View ArticleRe: High speed comparator eval board choices
Hi Ronnie, Apologies for the delayed of response. Before we could recommend parts, I need few more details about your applications: 1. What signal levels will the comparator input see?2. Do you need...
View ArticleHow to use Inter Core Communication on bf609?
Hi, everyone, I am trying to use BF609 Inter core communication. The BF609 cpu core A run uClinux, and I want to run software audio echo cancel module on BF609 cpu core B. I find some info about...
View Articleneed XML file for EVAL-ADV8003-SMZ-P
Matt,I am also unable to find the XML file needed for AVES3 to work with my EVAL-ADV8003-SMZ-P board. Could you post a link? Thanks
View ArticleRe: need XML file for EVAL-ADV8003-SMZ-P
Due to the complexity of this board, we were thinking it might be more user-friendly to use the SW driver rather than scripts to configure the board. I assume this kit included a remote control. Were...
View ArticleRe: ADV7619 simultaneous operation
Can you provide more details on what you are trying to do? -Matt
View ArticleRe: ADUC7020 eval. board software
Board Type : ADuC7020 Eval. Board Rev A2. QuickStart Plus. I searched installed directory (ADuC7XXXV0.2) and (/Keil/Arm/Boards/ADI/ADuc702x), but I can't find board related source codes.When I power...
View ArticleRe: bf609 eppi2 transmit data
have you completed it? if not ,you can try: change ENUM_EPPI_CTL_DLEN08 to ENUM_EPPI_CTL_DLEN16, Even if your hardware is in 8bit mode. i met the similar.
View ArticleRe: ADV3221 IBIS model
Dear Jonathan Thank you very much for your quick answer. ADV3221 is analog device, so it needs SPICE model to simulate, I think too.But in this case, I would like to check only the transmission...
View ArticleCan I use usb and ucfs in bf609_coreB?
HI, Can I use usb and ucfs in bf609_coreB? When I coreB added ucfs, will lead coreA error.TF card initialization and read-write file failed. I joined the two macros defined in the preprocessing :...
View ArticleRe: demodulation sin o square wave?
You can use a sine wave but it it must have a minimum drive level (see Figure 22). Even when you drive the LO input with a sine wave, that signal gets turned into a square wave inside the AD8333...
View ArticleRe: Default setup of ADV7441A
Hello Dave, Thank you for making the time for my question. Best regards,Kou
View ArticleADV7611 and ADV7610 Video format
Hello all, We can not find description of Quarter HD(960*540) about PRIM_MODE[3:0] VID_STD[5:0] in datasheet.If above can be supported. Please let me know how to do it. Regards,
View ArticleADV7611 free run mode
Hello all, When we set HDMI_FRUN_EN=1 and change to Free run,Cycle of HS and VS signal become unstable.After that, Cycle become stable.As the result of our check, 80ms is needed by stability of VS...
View ArticleAD9777 overall delay
Hi I am using the AD9777 in an existing design of a digital feedback controller, so actual input-to-output time delay is critical. What is this delay for the AD9777? (the datasheet only gives the...
View ArticleRe: Signal latancy in the ADV7181C and ADV7392.
For he combination of AD and Intersil, the pixel clock rate is 13.5 MHz (Since Intersil's serializer needs 13.5MHz clock rate). If I convert this into time it is 0.074us. You mentioned the delay in CP...
View ArticleRe: [ADV7511W] HDMI v1.4a, HDCP v1.3.
Hello, Thank you very much for your reply.Please fix the typo of the datasheet. Thank you.Best regards.
View ArticleUSBi now for $80!!
Down from $185 I think...Is this a holiday promotion or stock clearance before the new programmer based on XMOS is introduced?
View ArticleRe: ADV7619 simultaneous operation
Hello, I ask the question of ADV7619 dividing two thread.I wrote the detail below thread.http://ez.analog.com/message/125762#125762 We use two ADV7619 and we ask if ADV7619 support 4K2K@60p.Regards,
View Article