Re: Eliminating the cable capaciance
Hi, Iam using it with the range extension circuit. Its supposed to measure the capacitance b/w exc and cin. But i guess there's some leakage to ground through cable capacitance. Is there some way to...
View ArticleADIsimADC in MATLAB2011
Hi, I'm trying to use ADIsimADC as the source of data for a research in my university. Using the VisualAnalog interface everything is fine, but seeing as I need data from many frequencies and...
View ArticleRe: ADV7182,ADV7340 and ADV7511 video decoder/encoder configuration
Hi , We are using ADV7511 for DVI Out , ADV7182 for CVBS Input and ADV7341 for CVBS output. ADV7511 working properly as per expected. ADV7182 register configuration is done as shown in the attached...
View ArticleUsing the ADAU1700/1701 DSP for Radio Communications
We are currently working on a multimode radio transceiver and one of the functions we wanted to add was DSP primarily for audio signal processing on SSB receive. This in reality is a low intensity...
View ArticleRe: ADXL362 datasheet questions
Hi, 1. You can find that in item 6, the part begins the measurement in wake-up mode, this means the ODR is around 6Hz, then 30 samples means 5 seconds.2. Half_BW does not impact ODR, it only impact...
View ArticleRe: Exceed Input Common Mode Voltage
Hi Tino, I'm sorry for missing your last question. Would you mind letting me know what your circuit configurations are? We will be asking the designer so he can give some insight on what's happening...
View ArticleRe: ADL5350 Mixer
Hi, Georgy, Thank you very much for your reply.We understand what you mentioned.We would like to know the NF of Figure 59 circuit if you measured it. Best regards, Nikkee
View ArticleSchedule of CM40x BSDL Files
Hello, I' d like to know CM40x BSDL file release schedule. Is it a same timing a device production?Thank you for your help as always.Best regards,Sofy
View ArticleRe: unable to mount jffs2 file system in bf548
Thanks for the detailed information, to boot and mount the rootfs from a uImage, you should revert the kernel command line back in u-boot environment, it should be something like "init = /dev/mtdblock0".
View ArticleADV7611 TMDS PLL
Hi, Using ADV7611 in our closed system, TMDS PLL may not be able to lockwhen a random TMDS frequency signal from tens MHz to hundreds MHz is inputfor a few seconds then normal signal is input into...
View ArticleRe: The full scale of AD7687
Ryan_Curran wrote: To provide the correct impedance translation, which is the point of the amplifier, you will need to use a buffer per input leg. -- RyanI have schemata based AD7687 which didn't need...
View ArticleAudio Amplifier
I am searching for a good Audio Amplifier for my 2x 8 Ohm Speakers and i put the SSM2315 and SSM2375 Eval boards to be tested.Both of them werent loud enought for my application. The SSM2315 has a 6dB...
View ArticleRe: AD9559 : 0.1Hz loop bandwidth
Hi Paul, Thank you for your advice. I've tested increasing the phase lock threshold, and the DPLL can phase lock about 200ns phase lock threshold.We succeed in G.8262 wander test, but I'm not sure this...
View ArticleBlackfin as Video CODEC
Hi,I want to compress and decompress the video signal. To achieve this I am thinking to Implement H.264 codec in Blackfin, for this will you provide the required library files or firmware.Is the...
View ArticleRe: SIGBUS Error while debugging using gdbserver on BF609
Hi Zaheer, are you able to provide the C source code with a general description about the environment so I can run it on my side?
View ArticleRe: 21261 sometimes swaps left and right I2S data?
Hi, Can you provide more details regarding your application code. Are you using external clock and frame sync for the SPORT operation in I2S mode? Kindly explain how are you initializing SPORT in your...
View ArticleRe: SIGBUS Error while debugging using gdbserver on BF609
Hi Aaron We are writing code in assembly language only and the code I gave in the previous post is what we used and this is where I am facing the problem. In terms of the environment, we are using the...
View ArticleRe: The full scale of AD7687
Why did ADI show on the pagehttp://www.analog.com/en/content/Tested_Product_Combinations/fca.htmlTested Product Combinations which didn't use the full feature of ADC?
View ArticleRe: SHARC 21369 data I/O
Hi, Sorry for the delay in response. From your explanation I understand that you are trying to figure out the processing time you have before receiving another set of data from the SPORT. In the...
View Article