Re: Will the ADUC7023 init to default settings if the entire Flash is erase?
From this explanation I cannot figure out the problem and cannot give any feedback, it is not detailed enough and also I cannot see the picture attached. Can you provide more accurate details and the...
View ArticleRe: AD-FMComms2 HDL support for Altera FPGAs
That's the one. As far as I know, the LVDS direction on Altera devices is programmable. What I'm running into is that some FMC pins that your board requires to connect to LVDS pairs don't go to LVDS...
View ArticleADP5024: How to connect an unused Buck regulator
Hello, I was unable to find an answer to this in the datasheet... how should I connect the following ADP5024 pins if I do not want to use the second Buck regulator? VIN2, VOUT2, SW2, FB2, PGND2...
View ArticleClik here to view.
Re: ADA4096-2 & the Filter Wizard
groger, I'd like to attempt to clarify some of the Filter Wizard results, using a simpler design as an illustration. If you still have questions about your specific design, please feel free to...
View ArticleSome general questions on ADAU1452 from a newbie (to this chip)
Hi I seem to recall someone saying that you are now able to write your own modules for sigma DSPs and use sigma studio to join up your own modules with the standard ones. Is this the case? Is it...
View ArticleRe: ADM 1066 EEPROM Burning
After looking into the reserved area of EEPROM address space and not touching it, everything is working great! The other problems I had were because I didn't stop the Sequencing Engine while READING....
View ArticleRe: Circular Buffer problem in SIMD mode
Hi Krishna, I encountered the same exact issue recently. I believe the solution is correctly detailed in this thread:http://ez.analog.com/message/130390#130390 Regards,-Brian
View ArticleRe: ADuC7061 ADC temperature drift and reference resistor temperature drift
I agree with everything. ADuC7061 ADC is invalid without additional calibration in the temperature range -40°C - +40°C.
View ArticleRe: ADuC7061 ADC temperature drift and reference resistor temperature drift
Can you provide data you have captured as I explained as a first step?
View ArticleAD8099 oscillation
Hi,I use AD8099 as the output buffer of the AD768, for getting a ±1.1V output voltage. Specific circuit is in the attachment.When I test this circuit, I found AD8099 is oscillating. Is there any...
View Articlethermocouple amplification
hello, i am using t type thermocouples for the measurement. am looking for a instrumentation amplifier for the same. i found ad595 is suit for the this type of thermocouples. but the temperature limit...
View ArticleRe: AD8099 oscillation
dillian, You are using an op amp that is three times higher gbw than the AD811 on the eval board.Faster is not always better. I would use ADA4895-1, ADA4897-1, ADA4891-1 instead ofthe AD8099. With...
View ArticleRe: ADP5024: How to connect an unused Buck regulator
Hi Dave, I missed the Vin2 connection, and you are right, the Buck input pins Avin, Vin1, and Vin2 should be tied together.Thanks and regards,Jess
View ArticleRe: thermocouple amplification
Hello inayath, Yes, you can use a multiplexer for your application. You can check this thread for more information. I hope it helps!Kris
View ArticleRe: AD8253's "Input Common-Mode Voltage Range vs. Output Voltage"
Thank you Kris, I got your condition.Ok, If I find addtional question, then I will out it here again. Kaos
View ArticleRe: Building a program LDR bootable image for UBoot
This is for the ldr file generated in the CCES environment, it should be specified by a description file in CCES, I think you may need to open a thread in CCES support zone and get detailed information...
View ArticleRe: AD9957's power supply
Hi, Sittie I'm sorry that I forgot to do so. Yes, your answer did help me. Thanks very much! Best Regards!
View ArticleRe: EVAL-76XXEDZ connecting to an µC with 8-bit parallel Interface
Hi, Apologies for the delayed response. As you know, the stand-alone mode operation is further described on the page 3-4 of the user guide. The eval board has a gate array (U10 on the eval board) which...
View ArticleRe: Shall I get ESD HBM ?
Hi, Prasath. Attached file here is the updated list of the requested parts with its HBM ESD rating. regards,ahbie
View Article