Re: ADE7878 AVDD DVVD error
Hi Bhanuka Whatever you have explained right now seems to make sense, but to be sure that we are not over-looking anything can you share your system level connection schematic? When you connected the...
View ArticleRe: HDCP issues with AppleTV (7612 as the Rx)
Hi Reshmi, Unfortunately, that is just the bootloader. After the bootloader, the software driver should start running and print its version number. If you don't see this, type rev. -Matt
View ArticleRe: HDCP issues with AppleTV (7612 as the Rx)
I looked at your log file and it seems like you might be using an old version of the software driver. If you'll here:Advantiv™ EVAL-ADV7612-7511 Video Evaluation Boardyou can download the version 1.55...
View ArticleRe: HDCP issues with AppleTV (7612 as the Rx)
Thanks Matt. Will try it out. Can you give me the link to the user guide document too? Is it on the same page you sent earlier?
View ArticleRe: Maximum core clock for SSM2604 audio codec
Hello Joseph, I apologize for your question getting lost in the shuffle. I am taking some time today to look for old posts and found yours.Yes, you can use the MCLK frequencies listed in table...
View ArticleRe: HDCP issues with AppleTV (7612 as the Rx)
Hi Reshmi,There's a link on the EVAL-ADV7612-7511 page. It's UG-295. -Matt
View ArticleRe: ADV7441A sync detection
ADV7441A is not recommended for new designs. Depending on the functionality that you are needing, please consider using ADV7842 instead. Our support for ADV7441A is pretty much limited to the...
View ArticleClik here to view.
Re: HDCP issues with AppleTV (7612 as the Rx)
Hi Matt, Just uploaded the latest version 1.55 and I see the same problem unfortunately. Same behavior, I keep getting Aksv updates and every few seconds the downstream screen blanks out for a second....
View ArticleRe: AD5933 and AD5934 evaluation board software commands
Hey guys, I have been trying to open the labview code in labview 8 but it doesn't work. Can you plz guide me which labview version can be used?
View ArticleRe: Charc ADSP-21489 boot problem
In addition:Recorded in the flash swaping LDR file. After loading the kernel SPI activity is, apparently trying to read the data of the main program.Attach disasembler when connecting the emulator...
View ArticleCould ADV7403 support YPBPR/RGB 1080P30 component input?
Hi,We want to use ADV7403 to design a video system with YPbPr/RGB input.Could it support to 1080P30 analog component input? Another question is could ADV7393 support to 1080P30 output? We also want to...
View ArticleClik here to view.
Re: Could ADV7403 support YPBPR/RGB 1080P30 component input?
Correct the Another question is could ADV7393 support to 1080P30 output? We also want to develop a product with this encoder. In datasheet, there's some description about standards supported. Does it...
View ArticleADSP-TS101 Booting Option
Dear Analog Devices Team, We are using ADSP-TS101SAB1Z000 in one of our design, We have made strap pin /BMS as "0" so that the system boots from EPROM/Flash immediately after reset. In the ADSP-TS101...
View ArticleRe: ADAV803 problems
Hello Dave The workaround seems to be a good solution but i wish to know if there is a better one. Signal is braking constantly and periodicaly. I am switching it on and off for a longer and longer...
View ArticleAD9467EBZ ref design
Hello, I hope these queries haven't been answered in some other thread (I tried searching for them but couldn't find any).1) The custom peripheral added to the AXI bus in XPS is axi_adc_1c_0. This...
View ArticleRe: Interfacing ADAU1701 with AD1955
Apologies for the bump. Does there need to be a level shifter from the ADAU1701's 3.3V to the AD1955's 5V when using this buffer? Does the supply voltage of the buffer matter here?
View ArticleRe: AD9915 parallel write timing
Thanks for the clarification. Regarding IO_UPDATE and SYNC_CLK: I understand that one can write in parallel mode multiple registers before doing the IO_UPDATE, so the IO_UPDATE timing does not have to...
View ArticleClik here to view.
Re: ADAU1761 at non-audio sample rate (i.e. 51200)
Hello, Yes this is permissible. The data sheet allows for a MCLK period as short as 37 nS in 512 x fs mode. This corresponds to MCLK as high as 27 MHz, or a sample rate of 52.7 KHz. Thus,...
View ArticleAD5560 used for multiple power supplies
Hi, We are design engineers from the company, currently we have one project to adopt AD5560 for the power source design, we have LCD module driving with different power rails, totally we have five...
View ArticleRe: AD5560 used for multiple power supplies
We are developing the test fixture for LCD modules and our mass production will reach more than 30K per year, thanks.
View Article