Re: AD9467
Thanks for a great answer, i think i was confused about the timing diagram on figure 2 on page 7 before, but i makes more sense now. One last question. The 2 output bits on each differential pair, do...
View ArticleRe: Sigma300 (ADAU145x) Q&A
Bob, You are the best. Your test is much appreciated.It's really strange though. Which SigmaStudio version are you using?I'm running 3.11 Build 2, Rev 1396 (9/8/2014) and the limiter does not limit at...
View ArticleRe: ADV212 problem
HI,Are you Chinese? I'm using ADV212 too,and have the same questions you metioned. May be we can help each other
View ArticleRe: Some questions about ADV212
Hi Dave, There is a 8-bit gray-level raw image of 128 pixels X 128 pixels stored in a SRAM. All the pixels are active pixels. MCLK=20MHz,VCLK=20MHz. I use custom sepcific mode to put the image on VDATA...
View ArticleClik here to view.
Re: Sigma300 (ADAU145x) Q&A
Hello, I'm using the same version (3.11, build 2, rev 1386, 9/8/04). The discrepancy between the limiter's -10 dB threshold and the observed 0.5 (-6 dB) reading puzzled me as well. As it...
View ArticleADF4355-2 output range
Looking at the ADF4355-2 data sheet, it seems that the VCO tuning range covers 3400-6800 MHz, but the part's output frequency range only extends to 4400 MHz. Can you clarify what limits the usable...
View ArticleClik here to view.
Re: AD9361 issues found (using FMCOMMS5 and IIO SCOPE) requiring explanation
Hi,Another question related to the 9361 samples captured via IIO scope:When looking at the spectra of the captured signal replicas at multiples of 1/5 the sampling frequency (60MHz)When the signal is...
View ArticleClik here to view.
Re: question about blimp to design OSD
hi Jeyasudha: thank you for your kindly response. i have looked thourgh the user guides for blimp and i will try to read all of them clearly. Now in my side, we do not have the emulator...
View ArticleRe: About AD620 Make vs. Buy Error Budget
Hi Tarzan, Unfortunately, the datasheet for the AD620 was written over 20 years ago so we do not have a direct resource to provide you with this information. Most likely, it came from the...
View ArticleRe: Getting started with AD9837 and SPI
Hi, Are you going to(1) use the AD9837 evaluation board but using a different microcontroller, or(2) are you going to design your own board? If (1), just take note of the test points SCLK, SDATA and...
View ArticleRe: six analog device AD5422, connected in daisychain mode giving current...
Hi, Shivam. Would you be able to send a schematic diagram of the circuit? Have you checked/probed on the scope the digital data that is entering each SDI line of the 6 devices? What power supply level...
View ArticleRe: using AD8067 as inverting amplifier
Hi Niloy, If I may add on my previous response, the AD8067 is stable at gains > 8. As for your application, i think AD8067 is not the best part for you. Can you share your schematic of your...
View ArticleRe: order free samples
Hi, Have you tried the contacting Customer Service? You may click this link to go to the site: Analog Devices : Forms : Customer Service Support Regards,Mark
View ArticleRe: ADSP-21479 Software reset
Hi Raymond, Similar kind of issue is discussed by me in the engineer zone already, can you please look into the below thread.https://ez.analog.com/message/146620#146620 In the same thread you can find...
View ArticleClik here to view.
Re: AD9361 FMCOMMS3 Receiver performance at 500 MHz carrier frequency
Hi , I have attached the screen shots for the experiments done at 500 MHz and 1 GHz experiments. There are prominent 3rd Harmonics present for both the experiments. However the performance of the...
View Articlecan anybody suggest how to configure memory overlays in visual dsp++ 5.0 ide?
how to configure memory overlays in visualdsp++ 5.0 ide?
View ArticleClik here to view.
Re: technical document for your good ADV7626
OK,Dave,I will let him know this technical support data.Thanks,Kaos
View ArticleLook Detect Pin of HMC698LP5
If the customer does not use LD(pin#1), how he should treat LD pin?- Open?- 10kohm Pull up?- Connect to GND? In the HMC-EVB, LD pin is pulled up by 1lohm.Is this purpose turning on LED? BR, Tomo
View Article