Re: question about blimp to design OSD
Hi Xu tao, Good to know that you got answers and thanks very much for the update. Best Regards,Jeyasudha.M
View ArticleRe: six analog device AD5422, connected in daisychain mode giving current...
Hi, Shivam. Could you try writing to each part without using the daisy chain and check the output if it still shows erroneous values? Regards,Mark
View ArticleRe: Decreasing ADF5355 Lock Time
We are working on a solution to bypass the calibration routine to speed up lock times. This is just a property of the evaluation software, not the chip, right? It looks like clearing R0 bit 21...
View ArticleRe: How do the device EVAL AD5933EBZ is able to calculate the unknown...
I have studied that. But did not get the clarity of how the excel file generated has phase calculation and how the phase data is calculated in the device ???
View ArticleAD7687
I appreciate it if you could suggest me a AD7687 Datasheet explaining why the Common-Mode Input Range of AD7687 is up to VREF/2 + 0.1 V. Thank you for your help in advance.Best regards,Sofy
View Articleevaluate ADIS164007
can i evaluate ADIS164007 with ADIS164007 and ADISUSBZ? there are any software to evaluateADIS164007?
View ArticleAD5755 device placing usage when disable internal DC-DC converter.
Hello,When disable(not use) internal DC-DC converter, I would like to ask three questions as below.1) Is it OK that TWO AD5755 mounted PCB both side same position?2) Does Thermal pad need ”VIA" even...
View ArticleClik here to view.
Re: AD9467
Thanks for great help David! Would you then make the interface something like this in VHDL? diff. data ----- > IBUFGDS -----> IDDR2 ------> datadiff. clk ----- > IBUFDS ------>...
View ArticleRe: ADSP-21161N, RD and WR signal and waitstate under Synchronous Read/Write...
Hi, Please see my replies below: “Thus, I believe we must consider Figure 11 and Figure 19 at the same time, for the timing of Synchronous Read/Write as Bus Mater.Please correct me if I'm...
View ArticleRe: ADV7625 HDCP Problem
Hi Poornima, The software version is X2.2.2REL,and I just connect Sony BDP，and switch with other input ports which no-connect .And I have shut off the uart print.I will give you the log later.
View ArticleSelf-oscillation of HMC434E
The customer uses HMC434E.Does HMC434E have the self-oscillation? Even if he does not input the signal into HMC434E, it outputs a signal from OUT(pin#6) by self-oscillation.The frequency is 500 to...
View ArticleADuM4223 Output Impedance
Does anyone know what the output impedance of ADuM4223 (VOA & VOB) if there is no supply on VDDA and VDDB? I am thinking it is low input impedance because of the output pulsed sink resistance...
View ArticleRe: ADV7393 ED TEST BAR
I havn't ,I use my own board for ADV7393,I think there is not issue for the hardware ,becasue the SD video is sucessful(PAL) ,when I use the 'ED' pattern ,the test bar is error.so I can be sure the '...
View ArticleRe: six analog device AD5422, connected in daisychain mode giving current...
Hi, Shivam. Would you be able to measure the voltage on REFOUT pins of each unit? Also, would you be able to issue a software reset on the parts and check if the issue still persists? Regards,Mark
View ArticleRe: AD5755 device placing usage when disable internal DC-DC converter.
Hi, Sofy-san. I am curious as to why would you use the AD5755 without the DPC. Would you be able to share your reason? If you are going to continue without utilizing the DPC, I would refer you to...
View ArticleClik here to view.
Re: ADP1055 Evaluation Board For 7.4KW Solution
Another one:http://www.analog.com/static/imported-files/user_guides/ADP1046A_UG-734.pdf
View ArticleWhat's the Theta-Jc of ADM1066
Hi, Could you please help to provide the Theta-Jc of ADM1066 ; I can't find them in datasheet. Thanks!!
View Article