Re: Chinese ADXL345 board for $3?
Hi Tom, Thanks for sharing what you studied. I am also interested in how they control the cost. Checking the picture on website, I did not see anything wrong. Except ADXL345, there are also many cheap...
View ArticleRe: IBIS models for AD5441 & AD5446.
Hi Tar-Bow, The IBIS models are available under the tools, Software & Simulation Tab in the product page.However, as we are building this library, it is possible that the IBIS model for the part...
View ArticleADN2841 input to output propagation delay
Hello, Do you have any data for ADN2841 input to output(IMODP) propagation delay at 25C degree and Vcc=5V? Best regards and Thanks,Ian
View ArticleADV7623:How to output DTS/DOLBY on pin AP0_OUT
Dear My friendsPls refer to attached file. Audio source on my BlueRay player is DTS or DOLBY. Now I need this audio output to my SHARC decoder,I connect my ADV7623 to SHARC only use single pin...
View ArticleRe: ADV7630 720P performance less than 1080P resolution
Hi, Dave, they sed the "ADV7630-VER.1.2c.txt" script file, and ":01-02 Mux_function PCLK Freq 27Hz - 150MHz:" setting example; but for the current test result, the 1080P performance is good, for...
View ArticleRe: Save frames to hard drive using Video Input-Output project of adsp bf561
can you tell me where is Blackfin Forum
View ArticleRe: 16QAM with AD-FMCOMMS1-EBZ
Hi rgetz, w.e.f to the ADFMCOMMS-EBZ our Carrier board is KINTEX 7 SERIES we just want to check the Transceiver chain of ADFMCOMMS we had few queries regarding ADFMCOMMS w.e.f Discussion of Zynq...
View ArticleAD9249 Internal Vref Histogram
I have a question about AD9249. AD9249 has Internal Vref.Please send me AD9249 Internal Vref Histogram. Thank you.
View ArticleRe: How to set ADV7619 for Deepcolor
Thinks! I know 2x24bit mode can not output deepcolor video， in my design the subsequent processing is 8bit. So for deepcolor input, what we need is: adv7619 decodes the input video and truncate to 8...
View ArticleAbout ADV7341
There was a question about a reply from our customer. Please let me know about a question. >SDI (serial data interface) could still could still contain the higher frequency components.>It all...
View Articleinternal oscillator
Hi,I want to use AD5700-1 which has internal oscillator, thus the configuration I am applying to it is as XTAL_EN 1CLK_CFG1 1CLK_CFG0 0 then will the HART modem work? and what should make...
View ArticleAD9361_Tx_Path gain setting
Hi, I am using the AD9361 chip for my application. First i am working on Transmitter Path, for this i enabled clock output and i configured BBPLL, RF PLLs in both sections and i want to see LO leakage...
View ArticleRe: ADX345 read output problem
Hi Renan, Could you read DEVID correctly? I would suggest to read DEVID to check your read instruction firstly. Then, try to write a register and read back to see whether you can write a register...
View ArticleRe: AD9467-FMC with Zedboard and Vivado
Hi! Can you send me your design block in Vivado???
View ArticleQuery about information regarding weights of PLL components
Hi, there As part of a project which my team is doing, we are in need of PLL frequency synthesizers. I would be grateful to you if you can send me information regarding the weights of the following...
View ArticleRe: 16QAM with AD-FMCOMMS1-EBZ
HI Robin, w.e.f to the discussion regarding the ADFMCOMMS with carrier board KINTEX 7 Expected output from the on board modulator (ADL 5375) might be QPSK or 16 QAM w.e.f to the reference signal...
View ArticleRe: Sync Detection in ADV7441A
Hi Dave, yes the results are valid. There aren't glitches. The Register 0xb7 don't have an effect. martin sauer
View ArticleAccurate pulse Generation
I need to generate 10Hz Square pulse with Duty cycle of 0.1% i.e. Ton=100us, Toff=99.9ms, please suggest me with readily available ICs where i can change passive components to generate the pulse...
View ArticleAccurate pulse Generation
I need to generate 10Hz Square pulse with Duty cycle of 0.1% i.e. Ton=100us, Toff=99.9ms, please suggest me with readily available ICs where i can change passive components to generate the pulse...
View Article